View MC100H604_82982.PDF datasheet online --- IC-ON-LINE

Datasheet File OCR Text:

MOTOROLA
SEMICONDUCTOR TECHNICAL DATA
Registered Hex TTL/ECL Translator
The MC10H/100H604 is a 6-bit, registered, dual supply TTL to ECL translator. The device features differential ECL outputs as well as a choice between either a differential ECL clock input or a TTL clock input. The asynchronous master reset control is an ECL level input.. With its differential ECL outputs and TTL inputs the H604 device is ideally suited for the transmit function of a HPPI bus type board-to-board interface application. The on chip registers simplify the task of synchronizing the data between the two boards. The device is available in either ECL standard: the 10H device is compatible with MECL 10KH logic levels while the 100H device is compatible with 100K logic levels. * * * * * Differential 50 ECL Outputs Choice Between Differential ECL or TTL Clock Input Dual Power Supply Multiple Power and Ground Pins to Minimize Noise Specified Within-Device Skew
MC10H604 MC100H604
FN SUFFIX PLASTIC PACKAGE CASE 776-02
PIN NAMES
PIN D0-D5 CLK, CLK TCLK MR Q0-Q5 Q0-Q5 VCCE VCCT VEE FUNCTION TTL Data Inputs Differential ECL Clock Input TTL Clock Input ECL Master Reset Input True ECL Outputs Inverted ECL Outputs ECL VCC (0V) TTL VCC (+5.0V) ECL VEE (-5.2V)
LOGIC SYMBOL
1 OF 6 BITS Qn Qn
Dn
D
Q
TRUTH TABLE
Dn MR L L H TCLK/CLK Z Z X Qn+1 L H L
CLK R
L H X
Z = LOW to HIGH Transition
CLK CLK TCLK
Pinout: 28-Lead PLCC (Top View)
*
D0
26 27 28
D1 D2 VCCT D3
25 24 23 22
D4
21
D5 VCCE
20 19 18 17 16 15
Q5 Q5 Q4 Q4 VCCE Q3 Q3
MR VBB
TCLK VBB CLK CLK
2 3 4 5 6 7 8 9 10 11
14 13 12
*
1. When using MECL inputs, TCLK must be tied to ground (0V). 2. When using only one MECL input, the unused MECL input must be tied to VBB, and TCLK must be tied to ground (0V). 3. When using TCLK, both MECL inputs must be tied to VEE (-5.2V).
MR VCCE
Q0 Q0 VEE Q1 Q1 Q2
Q2
9/96
(c) Motorola, Inc. 1996
2-302
REV 1
MC10H604 MC100H604
DC CHARACTERISTICS: VEE = VEE(Min) to VEE(Max); VCCE = GND; VCCT = 5.0V +10%
0C Symbol S bl IEE ICCH ICCL Parameter P ECL Power Supply Current TTL Power Supply Current 10H 100H Min Max 130 130 35 45 Min 25C Max 130 140 35 45 Min 85C Max 130 150 35 45 Unit Ui mA mA Condition C di i
10H ECL DC CHARACTERISTICS: VCCT = +5.0 V 10%; VEE = - 5.20 V 5%
0C Symbol S bl IIH IIL VIH VIL VBB VOH VOL Parameter P Input HIGH Current Input LOW Current Input HIGH Voltage Input LOW Voltage Output Bias Voltage Output HIGH Voltage Output LOW Voltage Min 0.5 -1170 -1950 -1400 -1020 -1950 -840 -1480 -1290 -840 -1630 Max 225 0.5 -1130 -1950 -1370 -980 -1950 -810 -1480 -1270 -810 -1630 Min 25C Max 145 0.5 -1060 -1950 -1330 -910 -1950 -720 -1480 -1210 -720 -1595 Min 85C Max 145 Unit Ui A A mV mV mV 50 to - 2.0 V Condition C di i
100H ECL DC CHARACTERISTICS: VCCT = 5.0 V 10%; VEE = - 4.2 V to - 5.5 V
0C S bl Symbol IIH IIL VIH VIL VBB VOH VOL P Parameter Input HIGH Current Input LOW Current Input HIGH Voltage Input LOW Voltage Output Bias Voltage Output HIGH Voltage Output LOW Voltage Min 0.5 -1165 -1810 -1400 -1025 -1810 -880 -1475 -1280 -880 -1620 Max 225 0.5 -1165 -1810 -1400 -1025 -1810 -880 -1475 -1280 -880 -1620 Min 25C Max 145 0.5 -1165 -1810 -1400 -1025 -1810 -880 -1475 -1280 -880 -1620 Min 85C Max 145 Ui Unit A A mV mV mV 50 to - 2.0 V C di i Condition
TTL DC CHARACTERISTICS: VCCT = 5.0 V 10%; VEE = - 5.2 V 5% (10H version); VEE = - 4.2 V to - 5.5 V (100H version)
0C Symbol S bl VIH VIL IIH IIL VIK Parameter P Input HIGH Voltage Input LOW Voltage Input HIGH Current Input LOW Current Input Clamp Voltage Min 2.0 0.8 20 100 - 0.6 -1.2 Max Min 2.0 0.8 20 100 - 0.6 -1.2 25C Max Min 2.0 0.8 20 100 - 0.6 -1.2 85C Max Unit Ui V V A mA V VIN = 2.7 V VIN = 7.0 V VIN = 0.5 V IIN = -18 mA Condition C di i
AC CHARACTERISTICS: VCCT = 5.0 V 10%; VEE = - 5.2 V 5% (10H version); VEE = - 4.2 V to - 5.5 V (100H version)
0C Symbol S bl tPLH tPHL ts tH tPW VPP tr tf Parameter P Propagation Delay CLK to Q to Output TCLK to Q MR to Q Setup Time Hold Time Minimum Pulse Width CLK, MR Minimum Input Swing Rise/Fall Times 0.3 1.0 2.0 0.3 Min 1.5 2.0 1.5 1.5 1.5 0.5 0.5 1.0 Typ Max 3.5 4.0 4.0 Min 1.5 2.0 1.5 1.5 1.5 0.5 0.5 1.0 150 1.0 2.0 0.3 1.0 2.0 25C Typ Max 3.5 4.0 4.0 Min 1.5 2.0 1.5 1.5 1.5 0.5 0.5 1.0 mV ns 20% - 80% 85C Typ Max 3.5 4.0 4.0 Unit Ui ns Condition C di i CL = 50pF
ns ns ns
CL = 50pF CL = 50pF CL = 50pF
MECL Data DL122 -- Rev 6
2-303
MOTOROLA
MC10H604 MC100H604
OUTLINE DIMENSIONS
FN SUFFIX PLASTIC PLCC PACKAGE CASE 776-02 ISSUE D
B -N- Y BRK U D Z -L- -M- 0.007 (0.180)
M
0.007 (0.180)
M
T L-M
S
N
S S
T L-M
N
S
W
28 1
D
X VIEW D-D
G1
0.010 (0.250)
S
T L-M
S
N
S
V
A Z R C
0.007 (0.180) 0.007 (0.180)
M
T L-M T L-M
S
N N
S
H
0.007 (0.180)
M
T L-M
S
N
S
M
S
S
E 0.004 (0.100) G G1 0.010 (0.250)
S
K1
J
-T- VIEW S
SEATING PLANE
K F VIEW S 0.007 (0.180)
M
T L-M
S
N
S
T L-M
S
N
S
NOTES: 1. DATUMS -L-, -M-, AND -N- DETERMINED WHERE TOP OF LEAD SHOULDER EXITS PLASTIC BODY AT MOLD PARTING LINE. 2. DIMENSION G1, TRUE POSITION TO BE MEASURED AT DATUM -T-, SEATING PLANE. 3. DIMENSIONS R AND U DO NOT INCLUDE MOLD FLASH. ALLOWABLE MOLD FLASH IS 0.010 (0.250) PER SIDE. 4. DIMENSIONING AND TOLERANCING PER ANSI Y14.5M, 1982. 5. CONTROLLING DIMENSION: INCH. 6. THE PACKAGE TOP MAY BE SMALLER THAN THE PACKAGE BOTTOM BY UP TO 0.012 (0.300). DIMENSIONS R AND U ARE DETERMINED AT THE OUTERMOST EXTREMES OF THE PLASTIC BODY EXCLUSIVE OF MOLD FLASH, TIE BAR BURRS, GATE BURRS AND INTERLEAD FLASH, BUT INCLUDING ANY MISMATCH BETWEEN THE TOP AND BOTTOM OF THE PLASTIC BODY. 7. DIMENSION H DOES NOT INCLUDE DAMBAR PROTRUSION OR INTRUSION. THE DAMBAR PROTRUSION(S) SHALL NOT CAUSE THE H DIMENSION TO BE GREATER THAN 0.037 (0.940). THE DAMBAR INTRUSION(S) SHALL NOT CAUSE THE H DIMENSION TO BE SMALLER THAN 0.025 (0.635).
DIM A B C E F G H J K R U V W X Y Z G1 K1
INCHES MIN MAX 0.485 0.495 0.485 0.495 0.165 0.180 0.090 0.110 0.013 0.019 0.050 BSC 0.026 0.032 0.020 --- 0.025 --- 0.450 0.456 0.450 0.456 0.042 0.048 0.042 0.048 0.042 0.056 --- 0.020 2_ 10_ 0.410 0.430 0.040 ---
MILLIMETERS MIN MAX 12.32 12.57 12.32 12.57 4.20 4.57 2.29 2.79 0.33 0.48 1.27 BSC 0.66 0.81 0.51 --- 0.64 --- 11.43 11.58 11.43 11.58 1.07 1.21 1.07 1.21 1.07 1.42 --- 0.50 2_ 10_ 10.42 10.92 1.02 ---
MOTOROLA
2-304
MECL Data DL122 -- Rev 6
MC10H604 MC100H604
Motorola reserves the right to make changes without further notice to any products herein. Motorola makes no warranty, representation or guarantee regarding the suitability of its products for any particular purpose, nor does Motorola assume any liability arising out of the application or use of any product or circuit, and specifically disclaims any and all liability, including without limitation consequential or incidental damages. "Typical" parameters which may be provided in Motorola data sheets and/or specifications can and do vary in different applications and actual performance may vary over time. All operating parameters, including "Typicals" must be validated for each customer application by customer's technical experts. Motorola does not convey any license under its patent rights nor the rights of others. Motorola products are not designed, intended, or authorized for use as components in systems intended for surgical implant into the body, or other applications intended to support or sustain life, or for any other application in which the failure of the Motorola product could create a situation where personal injury or death may occur. Should Buyer purchase or use Motorola products for any such unintended or unauthorized application, Buyer shall indemnify and hold Motorola and its officers, employees, subsidiaries, affiliates, and distributors harmless against all claims, costs, damages, and expenses, and reasonable attorney fees arising out of, directly or indirectly, any claim of personal injury or death associated with such unintended or unauthorized use, even if such claim alleges that Motorola was negligent regarding the design or manufacture of the part. Motorola and are registered trademarks of Motorola, Inc. Motorola, Inc. is an Equal Opportunity/Affirmative Action Employer. How to reach us: USA/EUROPE/Locations Not Listed: Motorola Literature Distribution; P.O. Box 5405, Denver, Colorado 80217. 1-800-441-2447 MfaxTM: RMFAX0@email.sps.mot.com - TOUCHTONE 602-244-6609 INTERNET: http://Design-NET.com
JAPAN: Nippon Motorola Ltd.; Tatsumi-SPD-JLDC, 6F Seibu-Butsuryu-Center, 3-14-2 Tatsumi Koto-Ku, Tokyo 135, Japan. 03-81-3521-8315 ASIA/PACIFIC: Motorola Semiconductors H.K. Ltd.; 8B Tai Ping Industrial Park, 51 Ting Kok Road, Tai Po, N.T., Hong Kong. 852-26629298
MECL Data DL122 -- Rev 6 2-305
*MC10H604/D*
MC10H604/D MOTOROLA

▲Up To Search▲

Price & Availability of MC100H604

	To Download MC100H604 Datasheet File
If you can't view the Datasheet, Please click here to try to view without PDF Reader .